11/25/2023 0 Comments Alternative to smbup![]() To be honest, accessing NFS is horrible if you don’t own the correct windows license. Others need 3rd-party software to access NFS shares. If you own a Windows 7 Ultimate or Enterprise license, you can turn on Services-for-NFS inside Windows-Features. Net use X: \\IP-OF-YOUR-NAS\NAME-OF-SHARE /USER:YourUserName The line below mounts the SMB share to drive X:\ The SMB share can be mounted without any additional Software. Sudo mount IP-OF-YOUR-NAS:/NAME-OF-SHARE/ /mnt/nfs Network share access with Windows Sudo mount -t cifs //IP-OF-YOUR-NAS/NAME-OF-SHARE /mnt/smb/ -o user=YourUserName Later on you can replace this step with an entry inside /etc/fstab to mount your shares during startup. For testing purposes manually mounting is enough. With the following commands you will mount an SMB share into /mnt/smb and an NFS share into /mnt/nfs. Just play around and find the configuration which meets your requirements.Ĭreate folders inside /mnt (e.g. The upper hosts might get read access whereas the lower hosts might get additionally write access. You might split your network segment into two regions. As you can see below I have restricted read and write access to the network segment 10.10.0.0/24, which allows the access to a total amount of 254 hosts. Since NFSv4 it’s possible to use a Kerberos server, which extends the authentication system.Įnabling NFS and SMB in a Synology NAS (DSM) is done with a few clicks. However SMB provides a user-based authentication. This means that every user on an authenticated machine can access a specific share. NFS uses the host-based authentication system. An important difference between both protocols is the way they authenticate. I have decided to use NFSv4 and SMBv2 with large MTU. The bit rate between PC and FritzBox is set to 100 Mbit/s. The NAS device is linked to FritzBox with 1000 Mbit/s. It has a hard disk with a transfer rate of around 150 MB/s. The NAS device will be the target for read and write operations. I will show you a basic benchmark based on read and write operations with both protocols. Since SMB is supported by Windows, many company and home networks use it by default. I just wanted to share this, if it helps anyone.Both SMB and NFS are network protocols of the application layer, used mainly for accessing files over the network. I would LOVE to get this to work! Maybe this cleared up something for someone else to figure out that I don’t get the trix with naming the cover “1.metathumb” to work, as spoke of before. But for folder with movies inside, I can’t get it to choose the folder.jpg image that I want, it always choose the latest movie cover. This shows the cover for folder without movies directly inside. ![]() ![]() (BTW, This got the metadata download to work for me!) “Tv-show” AND “Season 1” folders), not only Tv-Show-folder. You also have to set ALL the folder to Read & Writable (ex. On Mac, right-click → Show info, at the bottom change everything to “Read & Write”. But the problem for me was that the image was set to “Not accessible” for anyone else then me (Loged in), I changed this to Everyone → Read & Writable. You can put “folder.jpg” in “Tv-show” folder. If you have movies in folder, and then this folder in another folder, maybe like Tv-shows: If its more then one movie, I think it takes the newest movie. If you have movies with cover (.metathumb) in a folder, it will set the foldercover to the same as the movie inside. Share 4 folders, Tv-Shows, Documentary, Movies and Cartoons. I have found out this.įirst thing first, I use latest firmware, Simple theme, Network share using SMBUp from Mac (Mountain Lion). I have read a lot about these problems with getting the folder.jpg image to show. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |